steering knuckle
英 [ˈstɪərɪŋ ˈnʌkl]
美 [ˈstɪrɪŋ ˈnʌkl]
网络 转向节; 羊角; 转向关节; 转向杯; 操纵关节
双语例句
- It was presented that a new precision forming technology of car steering knuckle in this paper.
文章提出了轿车转向节精密成形新工艺。 - Steering knuckle bearing grease nipple Design of Bearing Lubrication in Industrial Motors
工业电机滚动轴承油脂润滑方案设计 - Finite Element Analysis and Experimental Study of the Disc Steering Knuckle Die Forging
盘式转向节模锻的有限元模拟与实验研究 - A feasible process scheme was made for forming the steering knuckle of a truck based on a technological analysis on the forging of the part.
通过对卡车转向节锻件的工艺分析，制定了合理的工艺方案。 - The production of domestic, import models of the steering section of the main pin, steering knuckle kingpin repair kit is more popular with users alike.
所生产的国产、进口车型的转向节主销、转向节主销修理包更受广大用户的一致好评。 - The hub and bearing assembly does not require removal from the steering knuckle to replace wheel attaching studs in the hub and bearing assembly.
更换轮毂及轴承组件内的车轮固定螺桩无需自转向关节中取出轮毂及轴承组件。 - Tie Rod End To Steering Knuckle Nut
转向拉杆端与转向关节螺栓 - Simulation of Half-closed Extrusion Process for Steering Knuckle
转向节的一种半封闭式挤压成形工艺模拟研究 - Steering axis inclination is the inward tilt of the steering knuckle at the top.
转向轴倾角是向内倾斜的转向关节在顶部。 - Steering knuckle tie rod end pressure lubricator What welding methods do you use in connecting the plates, frames, and beams?
转向节横拉杆接头油嘴在焊接钢板，肋骨，甲板横梁时，你们用什么焊接方法？ - A Study of Forging Forming Process for Steering Knuckle of Light Truck
轻卡汽车转向节锻造成形工艺的研究 - Study on New Obturated Extrusion Precision Forming Technology of Car Steering Knuckle; bradenhead squeeze pressure
轿车转向节闭塞挤压精密成形新工艺研究关闭井口套管闸门形成的挤压压力 - Research and Development of a Real-Time Quality Monitoring System for Assembling Steering Knuckle Bearing
转向节轴承装配质量实时监控系统的研究与开发 - This backplate requires modification prior to installation on the steering knuckle.
杠杆，这背板需要修改的背板安装前关节。 - Steering knuckle tie rod end pressure lubricator Grayioc tubing joint
转向节横拉杆接头油嘴 - During steering maneuvers, the strut and the steering knuckle ( through the ball joint and a pivot bearing in the strut's upper retainer) turn as an assembly.
车辆转向时，支柱以及转向关节（经由球形接头与上支柱固定器之轮毂轴承）会一体旋转。 - FE analysis of the forging process of the automobile steering knuckle
汽车转向节锻造成形工艺的有限元分析 - Steering Knuckle Separation From Driveshaft
转向关节与驱动轴分离 - The trike frame should now be nearing completion and only requires the installation of the steering knuckle mounting plates to be complete.
该三轮车框架现在应该已接近完成，只需要安装指导安装板的关节完整。 - This movement is produced by gearing and linkage between the steering wheel in front of the driver and the steering knuckle ( or wheel).
这一运动是由装在驾驶员前面的转向盘与转向节（车轮）之间的转向器和连杆装置来共同完成的。 - Aimed at Jetta steering knuckle, the technology of two forging steps in one heat was presented, which combined precision pre-forging by extrusion-belt obliterated extrusion with open finish-forging.
以捷达轿车转向节为研究对象，制定了挤压带式可分凹模闭塞挤压精密预制坯和开式终锻成形相结合的“一火两锻”成形工艺。 - Remove the steering knuckle from the strut.
拆去连接支撑架到球销的固定夹。 - The effect of thermomechanical treatment on the microstructure and properties of the automobile steering knuckle was researched in this paper.
研究了汽车转向节锻后余热淬火工艺对钢的组织和性能的影响。 - Ductile Iron-Automotive Steering Knuckle's Casting Technology and Computer Analysis and Stimulation
球墨铸铁&汽车转向节的铸造工艺及计算机模拟仿真分析 - The results show that the thermomechanical treatment can improve the quality of the automobile steering knuckle.
结果表明，锻造余热淬火工艺对汽车转向节质量有明显改善。 - Study on New Technology of CAR Steering Knuckle
轿车转向节成形新工艺研究 - Loaded Vibration Test and Simulation for Steering Knuckle Arm
轿车转向节臂振动加载试验与仿真 - This paper focuses on the studies of the forging process design and the forging intelligent design of the steering knuckle.
针对以上问题，本文重点研究转向节的锻造工艺设计和锻造智能化设计。 - Structural statics analysis module using ANSYS conducts the strength analysis of the steering knuckle model.
利用ANSYS结构静力学分析模块进行了转向节强度分析。 - The steering knuckle, with many varieties and usage quantities, is mainly made from the forging process now.
转向节是汽车上的重要零件，品种多，用量大，目前主要通过锻造工艺进行生产。